External elements of the car body Audi A2

Removal and installation of the radiator frame with attachments
Remove bumper. Remove soundproofing. Remove the flexible cable in the hood latch shell. Disconnect plug connectors. Remove bumper cross member and...

Front fender — design description
Front fender: 1. Guide element 2. Combination bolt, 4 Nm 3. Hexagon bolt, 4 Nm 4. Shoulder bolt. For horizontal adjustment, unscrew or screw in as required....

Horizontal wing adjustment
1. Shoulder bolts (for horizontal adjustment, screw or unscrew as required, when tightening the nuts, secure the flanged bolts against turning with a hexagon...

Wing stop — removal and installation
Remove bumper. Unscrew bolts -1- and -3- and remove guide -2-. When installing, tighten screws to 1.5 Nm.

Noise isolation — design description
1. Noise isolation. Loosen the screws and remove the soundproofing. When installing, insert the bumper pad into the noise insulation as shown in the upper...

Removal, installation and adjustment of a cowl
1. Hood. To remove, unlock the hood. Slightly lift the hood towards the front from the mountings and remove it from the vehicle. Cover bonnet with protective...

Hood unlock
Loosen the lock by turning it to the left and slightly lift the hood forward from the fasteners. To remove the retainer cap -1-, unscrew the nut -2- from the...

Removal and installation of facing of a cowl and an air inlet
1. Hood 2. Buffer for height adjustment. To adjust the hood, turn the bumper out until it touches the fender. When properly adjusted, the buffer is in contact...

Removal and installation of a cable drive of a cowl
1. Cable drive hood. Remove the storage compartment on the driver's side. Remove A-pillar lower trim. Remove bolt. Remove cover. Disconnect the sheathed...

Removal and installation of a cover of a drainage box
1. Drainage box cover. Remove the hood. Remove windshield wipers. Remove the gasket towards the front. Remove the plenum box cover from the clamping strip at...

Fixing the cover of the drainage box
Press the profile -1- of the plenum chamber cover into the retaining strip -2- of the windshield -3- when fitting.

Removal and installation of a forward bumper
1. Cover. Removal: Loosen the front fender liner. Loosen screws. Press the rivet pins in until they click into place. The pin is not fully included. Pull out...

Removing the cover from the wing
To remove the cover -1- unscrew the Tox bolts -2-. On the engine side, release the catch -arrow- and press out the cover from the side. Remove cover from...

Removing the fog lamp cover
Use a screwdriver to unlock the catches -arrows- on the trim. First, remove the lining from the inside of the vehicle, and then remove it from the side of the...

Removing the air intake grille
The side pads have been removed. To remove, press the catches -arrows- together piece by piece and pull the air intake grille out of the cover.

Removal and installation of a back bumper
1. Guide profile 2. Bolt, 2 Nm 3. Self-tapping screw, 1.5 Nm 4. Amplifier profile. Before removing, remove the bumper cover. Completely unscrew the bolts and...

Removal and installation of a rear-view mirror
1. Rear view mirror. To remove, remove the door trim. Remove cover. Disconnect plug connector from mirror adjuster. Loosen the bolt and remove the gasket....

Removal and installation of the case of a rear-view mirror
1. Togh bolts, 1 Nm 2. Lid 3. Mirror glass. In order to avoid damage to the mirror body, tape it from below and above with adhesive tape on a textile basis....

Replacement of mirror glass and mirror adjusting element
Before removing the mirror glass, secure the mirror housing at the top and bottom with adhesive tape. Separate the mirror glass -3- using the lever -80-200-...

Removal and installation of a forward fender liner
Instruction. Depending on the configuration, the fender liner slightly differs in the location and number of fasteners. 1. Front fender liner. Before removal,...

Removal and installation of a back fender liner
1. Rear fender liner. Before removal, dismantle the rear wheel. Loosen the bolts. Press the rivet pins, remove the rivets and remove the fender liner from the...

Removal and installation of mudguard apron
1. Mounting bracket 2. Combination bolt, 4 Nm 3. Self-tapping screw, 1.5 Nm 4. Bracket 5. Combination bolt, 4 Nm 6. Shoulder bolt, 1.5 Nm 7. Mudguard apron....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Audi A2(1999-2005)