![](https://www.audimanual.ru/img/q/2534.jpg)
I 1. Charisma switching module -E592-. Installation location: Charisma switch module -592- installed in the front panel; 2. Used electronic damping control system -J250-. Installation location: The control unit for electronic damping control -J250- is located in the rear right side trim of the luggage compartment. When replacing the electronic damping control unit -J250-, the standard suspension position must be readjusted. After recalibrating the adjustment position on vehicles with lane assist, the lane departure warning control unit -J759- must be recalibrated; 3. Shock absorber with rear right shock absorber control valve -N339-; 4. Rear left ride height sender -G76- and rear right ride height sender -G77-. When removing and installing rear left ride height sender -G76- and rear right ride height sender -G77- or removing linkage on vehicles with electronic damping control, the standard suspension position must be readjusted. After recalibrating the adjustment position on vehicles with lane assist, the lane departure warning control unit -J759- must be recalibrated. For vehicles with an automatic transmission and headlight range control, perform the basic installation of the headlights; 5. Vehicle acceleration sensor, rear -G343-; 6. Shock absorber with rear left shock absorber control valve -N338-; 7. Front left vehicle acceleration sensor -G341- and front right vehicle acceleration sensor -G342-; 8. Shock absorber with front left shock absorber control valve -N336-; 9. Front left ride height sender -G78- and front right ride height sender -G289-. When removing and installing the front left ride height sender -G78- and the front right ride height sender -G289- or removing the linkage on vehicles with electronic damping control, the standard suspension position must be readjusted. After recalibrating the adjustment position on vehicles with lane assist, the lane departure warning control unit -J759- must be recalibrated. For vehicles with an automatic transmission and headlight range control, perform the basic installation of the headlights; 10. Shock absorber with front right shock absorber control valve -N337-
Removing the electronic damping control control unit -J250-
The used electronic damping control system -J250- is located in the rear right side luggage compartment trim. Turn off the ignition. Remove the right trunk compartment lid. If there is a trailer recognition control unit -J345--1-, detach it from the bracket -2-. Unscrew nuts -arrows-, remove control unit bracket -2- from threaded bolts and lower down.
![](https://www.audimanual.ru/img/q/2535.jpg)
Unfasten clamps -A- and -B- and remove electronic damping control unit -J250- -1- from bracket -2-. Disconnect electrical connector -3- and remove electronic damping control unit -J250- -1-. Remove electronic damping control unit -J250- -1-.
![](https://www.audimanual.ru/img/q/2536.jpg)
Installation
Installation is carried out in the reverse order; a new adaptation of the electronic damping control unit -J250- must be carried out.
Removing front left vehicle acceleration sensor -G341- and right -G342-
Raise the car. Unlock and disconnect the plug connector -2-, Unscrew the nuts -1 - and remove the sensor -3- from the bracket -3-.
![](https://www.audimanual.ru/img/q/2537.jpg)
Installation
Install in reverse order. Please note the following: When installing, take into account the mounting position of the sensor. Install sensor -4- as shown in the figure. Tighten nuts -1 to a torque of 8 Nm. Tightening torque for nuts -5-: 5 Nm.
Removing rear vehicle acceleration sensor -G343-
Remove the rear left wheel. Remove the rear left fender liner. Unlock and disconnect plug connector -2-. Unscrew bolts -1- and remove sensor -3-.
![](https://www.audimanual.ru/img/q/2538.jpg)
Installation
Install in reverse order. Please note the following: When installing, take into account the mounting position of the sensor. Install sensor -3- as shown in the figure. Tighten bolts -1- to 5 N'M.
Visitor comments