To erase the previous information, press for more than 2 s on the key with the inscription «Reset» in the middle of the key «Computer» Warning signals (see below «travel time» And «power reserve») released by pressing a key «Reset». This key is also used to set the time.
Times of Day
To display the current time, press the lower part of the computer control key with the ignition on. On the screen, the triangle will show the lower left symbol on the tachometer dial.
To set the time of day, do the following:
- press the lower part of the control key for at least 3 seconds until the minutes indication starts flashing;
- release the control key;
- briefly press the key «Reset», to display the next minute, to speed up the passage of minutes, press the key for a long time,
- after setting the exact minutes, press the lower part of the control key until the hour indication starts flashing;
- briefly press the key «Reset» to change the time by 1 hour ahead and permanently for the accelerated passage of the hour indication;
- after setting the correct time, press the upper part of the control key.
Travel time
The trip time countdown is programmed with the ignition on by pressing the top of the control button until the triangle points to the symbol located in the upper left corner of the screen.
The display shows the travel time since the last reset of the computer's memory. When the ignition is turned off, the previously displayed information about the trip time is stored in the computer's memory. When the trip is continued, the trip time is added to the previous one. The maximum countdown time is 23 h 59 min.
If you need to record the trip time starting from this moment, set the time count to zero by pressing the button «Reset».
Warning signal
After 2 hours of driving, with any indication on the display, information is automatically displayed «Travel time» flashing light «2,00». To remove the travel time indication, briefly press the button «Reset».
If the trip is interrupted for less than 10 minutes, the warning signal will automatically sound after 2 hours, i.e. in total after 4 hours «4,00» etc.
If the trip is interrupted for more than 10 minutes with the ignition off, the warning alarm will automatically reset to zero.
Average fuel consumption
With the ignition on, press the control button several times to light up the control triangle, pointing at the center symbol above the top edge of the display. The fuel consumption indicated on the display corresponds to the average consumption in liters per 100 km since the last reset of the display to zero.
After switching off the ignition, the value of the average consumption is stored in the memory and continues to take into account the fuel consumption after the resumption of the trip.
To reset the readings to zero, press the key «Reset».
Average moving speed
Proceeding as for the previous functions, draw a triangle with a tip against the rightmost uppermost symbol above the display. The display shows the average travel speed in 3 km/h since the speed display was last reset to zero.
When the ignition is turned off, the indication goes into the computer's memory and, after the trip is resumed, is recalculated taking into account the previous speed.
To clear the memory of previous readings, press the key «Reset».
Power reserve
Proceed as described for the previous functions and position the control triangle against the left character above the top edge of the display.
The screen shows the reserve mileage, calculated in segments of 10 km, with the remaining fuel in the tank, provided that the driving style is maintained. The range is calculated based on fuel consumption over the previous 30 km. If you change to a more economical driving style, the range may increase.
Warning signal
If the remaining range is less than 50 km, the display shows the range information instead of any previous information.
The power reserve indicator lights up with a flashing light, if there is less than 5 liters of fuel left in the fuel tank, the letter lights up «L» - empty tank.
This indication is removed by pressing the computer control key or the key «Reset».
If fuel has not been refueled, a warning signal is displayed each time the ignition is turned on.
Current fuel consumption
Follow the same operations as for the above functions and display the control triangle opposite the symbol at the bottom right of the display edge.
The screen shows information about fuel consumption in liters per 100 km for the last 30 km of the journey.
When the speed decreases, the display shows «zero». When the car stops, the latest data on the current fuel consumption is transferred to the computer's memory.
When you press the accelerator pedal while the vehicle is stationary and the engine is idling, the display may show a very high current fuel consumption.
Visitor comments